WRT3200ACM refuses to embrace 3rd party firmware

[hermes77]

Long story short I can't figure out what I'm doing wrong but no matter what I try I can't get any non linksys firmware to boot past the launching kernel stage; I've followed your instructions and those found on the openwrt forum/wiki to install McDebian and/or OpenWrt to no avail. Firmware appears to flash without error but no connection between router and computer ever occurs. Serial communication ceases to show any indication of change/receipt of input etc. Obviously you'll need more info to diagnose the problem (if you even feel like figuring it out with me) I'll happily provide dumps/any info requested. Thanks for making McDebian even if I haven't been able to use it yet.

[chadster766]

Please post the console output of your firmware load process.

Just to confirm. After you load a 3rd party firmware you don't loose serial console access?

[hermes77]

Here is the post firmware flashing attempts to boot McDebian log any time I restart the router it's due to hanging and lack of response to ping, tftp, serial commands etc. I'll attempt to re flash and post logs as soon as I get home. And on both 3rd party and linksys firmware serial console is unresponsive after it loads the firmware

BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client capabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:2, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:3, next_record:2

[auto_recovery_init] BOOT_COUNT_TO_RECOVERY
[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x221000

Updating boot_count ...
[boot_count_write] offset:0x221000 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
#### auto_recovery:1 ####
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: linux
Created: 2019-12-24 3:55:08 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4929881 Bytes = 4.7 MiB
Load Address: 00200000
Entry Point: 00200000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

(except it doesn't it hangs instead)

BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:1, next_record:3

[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x221800

Updating boot_count ...
[boot_count_write] offset:0x221800 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0

Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 200mA)
SanDisk Cruzer Glide 20043514410EF1C3946E

Marvell>> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Mass Storage, USB Revision 2.0
- SanDisk Cruzer Glide 20043514410EF1C3946E
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x0781 Product 0x5575 Version 1.38
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
Marvell>> usb dev 0

USB device 0:
Device 0: Vendor: SanDisk Rev: 1.26 Prod: Cruzer Glide
Type: Removable Hard Disk
Capacity: 15267.0 MB = 14.9 GB (31266816 x 512)
... is now current device
Marvell>> usb part

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 31264768 53c1812e-01 83
Marvell>> usbboot dev 0

Loading from usb device 0, partition 1: Name: usbda1 Type: U-Boot
(router hangs mockingly)

[chadster766]

Thanks,

I've looked this over and don't see what the issue is.

We can get a better idea of what going on with your firmware loading output.

[hermes77]

Sorry my work/sleep schedule is the worst
Here is my most recent attempt, and the router still refuses to do anything other than imitate a paperweight after reciting its famous last words:
"Starting kernel"

BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:2, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:3, next_record:8

[auto_recovery_init] BOOT_COUNT_TO_RECOVERY
[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x224000

Updating boot_count ...
[boot_count_write] offset:0x224000 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
#### auto_recovery:1 ####
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0
Marvell>> setenv serverip 192.168.1.2
Marvell>> setenv ipaddr 192.168.1.1
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
altFwSize=0x5000000
altKernAddr=0x5a00000
altKernSize=0x0600000
altnandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock8 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $altKernAddr $altKernSize; bootm $defaultLoadAddr
auto_recovery=yes
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
boot_part=1
boot_part_ready=3
bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run nandboot
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr;
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
defaultLoadAddr=0x2000000
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=60:38:E0:D0:50:00
eth1mtu=1500
eth2addr=60:38:E0:D0:50:00
eth2mtu=1500
eth3addr=60:38:E0:D0:50:00
eth3mtu=1500
ethact=egiga0
ethaddr=60:38:E0:D0:50:00
ethmtu=1500
ethprime=egiga0
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
firmwareName=rango.img
flash_alt_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $altKernAddr $filesize
flash_pri_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand write $defaultLoadAddr $priKernAddr $filesize
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.1
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
limit_dram_size=yes
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:17:06:0d
nandEcc=nfcConfig=4bitecc
nandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $priKernAddr $priKernSize; bootm $defaultLoadAddr
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
priFwSize=0x5000000
priKernAddr=0x0a00000
priKernSize=0x0600000
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
run_script=no
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
sd_detection_dat3=no
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
update_both_images=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $priKernAddr $filesize && nand write $defaultLoadAddr $altKernAddr $filesize
usb0Mode=host
usbActive=0
usbType=2
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81

Environment size: 4491/131068 bytes
Marvell>> wget
Unknown command 'wget' - try 'help'
Marvell>> curl
Unknown command 'curl' - try 'help'
Marvell>> sys
sys_restore sysboot
Marvell>> setenv firmwareName McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img
Unknown command 'setenv' - try 'help'
Marvell>setenv firmwareName McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img
Unknown command 'setenv' - try 'help'
Marvell>> setenv firmwareName McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img
Marvell>> savenv
Unknown command 'savenv' - try 'help'
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
Marvell>> run update_both_images
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img'.
Load address: 0x2000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Marvell>> run update_both_images
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########
4.5 MiB/s
done
Bytes transferred = 4929945 (4b3999 hex)

NAND erase: device 0 offset 0xa00000, size 0x5000000
Erasing at 0x59e0000 -- 100% complete.
OK

NAND erase: device 0 offset 0x5a00000, size 0x5000000
Erasing at 0xa9e0000 -- 100% complete.
OK

NAND write: device 0 offset 0xa00000, size 0x4b3999
4929945 bytes written: OK

NAND write: device 0 offset 0x5a00000, size 0x4b3999
4929945 bytes written: OK
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
altFwSize=0x5000000
altKernAddr=0x5a00000
altKernSize=0x0600000
altnandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock8 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $altKernAddr $altKernSize; bootm $defaultLoadAddr
auto_recovery=yes
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
boot_part=1
boot_part_ready=3
bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run nandboot
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr;
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
defaultLoadAddr=0x2000000
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=60:38:E0:D0:50:00
eth1mtu=1500
eth2addr=60:38:E0:D0:50:00
eth2mtu=1500
eth3addr=60:38:E0:D0:50:00
eth3mtu=1500
ethact=egiga0
ethaddr=60:38:E0:D0:50:00
ethmtu=1500
ethprime=egiga0
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
fileaddr=2000000
filesize=4B3999
firmwareName=McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img
flash_alt_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $altKernAddr $filesize
flash_pri_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand write $defaultLoadAddr $priKernAddr $filesize
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.1
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
limit_dram_size=yes
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:17:06:0d
nandEcc=nfcConfig=4bitecc
nandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $priKernAddr $priKernSize; bootm $defaultLoadAddr
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
priFwSize=0x5000000
priKernAddr=0x0a00000
priKernSize=0x0600000
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
run_script=no
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
sd_detection_dat3=no
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
update_both_images=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $priKernAddr $filesize && nand write $defaultLoadAddr $altKernAddr $filesize
usb0Mode=host
usbActive=0
usbType=2
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81

Environment size: 4575/131068 bytes
Marvell>> reset
resetting ...

BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:1, next_record:9

[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x224800

Updating boot_count ...
[boot_count_write] offset:0x224800 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: linux
Created: 2019-12-24 3:55:08 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4929881 Bytes = 4.7 MiB
Load Address: 00200000
Entry Point: 00200000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

[chadster766]

Thanks I'm looking it over and doing some comparisons. I will get back to you on this.

[chadster766]

Nothing sticks out as to what's causing the issue.

Please post an attempt to load the latest OpenWRT firmware.

[hermes77]

I'm eating breakfast and flashing router with openwrt shortly, but I noticed rhat McDebian isn't listed as a 3rd party firmware here . It might help spread the word about the awesome work you've done if it was.

[hermes77]

Sorry got called into work, here's my attempt to flash openwrt 19.07.8


BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED
l

U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:2, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:3, next_record:14

[auto_recovery_init] BOOT_COUNT_TO_RECOVERY
[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x227000

Updating boot_count ...
[boot_count_write] offset:0x227000 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
#### auto_recovery:1 ####
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0

Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
altFwSize=0x5000000
altKernAddr=0x5a00000
altKernSize=0x0600000
altnandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock8 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $altKernAddr $altKernSize; bootm $defaultLoadAddr
auto_recovery=yes
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
boot_part=1
boot_part_ready=3
bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run nandboot
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr;
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
defaultLoadAddr=0x2000000
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=60:38:E0:D0:50:00
eth1mtu=1500
eth2addr=60:38:E0:D0:50:00
eth2mtu=1500
eth3addr=60:38:E0:D0:50:00
eth3mtu=1500
ethact=egiga0
ethaddr=60:38:E0:D0:50:00
ethmtu=1500
ethprime=egiga0
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
fileaddr=2000000
filesize=4B3999
firmwareName=McDebian-Buster-WRT3200ACM-V1-FW_VER1_kernel_4.19.91.img
flash_alt_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $altKernAddr $filesize
flash_pri_image=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand write $defaultLoadAddr $priKernAddr $filesize
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.1
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
limit_dram_size=yes
loadaddr=0x02000000
loads_echo=0
mtddevname=uboot
mtddevnum=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:17:06:0d
nandEcc=nfcConfig=4bitecc
nandboot=setenv bootargs console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk $mtdparts;nand read $defaultLoadAddr $priKernAddr $priKernSize; bootm $defaultLoadAddr
netbsd_en=no
netmask=255.255.255.0
netretry=no
partition=nand0,0
pcieTune=no
pexMode=RC
priFwSize=0x5000000
priKernAddr=0x0a00000
priKernSize=0x0600000
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
run_script=no
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
sd_detection_dat3=no
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
update_both_images=tftpboot $defaultLoadAddr $firmwareName && nand erase $priKernAddr $priFwSize && nand erase $altKernAddr $altFwSize && nand write $defaultLoadAddr $priKernAddr $filesize && nand write $defaultLoadAddr $altKernAddr $filesize
usb0Mode=host
usbActive=0
usbType=2
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81

Environment size: 4628/131068 bytes
Marvell>> setenv firmwareName openwrt-19.07.8-factory
Marvell>run flash_pri_image
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-19.07.8-factory'.
Load address: 0x2000000
Loading: *
TFTP error: 'File not found' (1)
Not retrying...
Marvell>> setenv firmwareName openwrt-19.07.8-factory.img
Marvell>> run flash_pri_image
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-19.07.8-factory.img'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########
5.1 MiB/s
done
Bytes transferred = 10616832 (a20000 hex)

NAND erase: device 0 offset 0xa00000, size 0x5000000
Erasing at 0x59e0000 -- 100% complete.
OK

NAND write: device 0 offset 0xa00000, size 0xa20000
10616832 bytes written: OK
Marvell>> run flash_alt_image
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-19.07.8-factory.img'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########
5.2 MiB/s
done
Bytes transferred = 10616832 (a20000 hex)

NAND erase: device 0 offset 0x5a00000, size 0x5000000
Erasing at 0xa9e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x5a00000, size 0xa20000
10616832 bytes written: OK
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
Marvell>> run update_both_images
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-19.07.8-factory.img'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########
5.2 MiB/s
done
Bytes transferred = 10616832 (a20000 hex)

NAND erase: device 0 offset 0xa00000, size 0x5000000
Erasing at 0x59e0000 -- 100% complete.
OK

NAND erase: device 0 offset 0x5a00000, size 0x5000000
Erasing at 0xa9e0000 -- 100% complete.
OK

NAND write: device 0 offset 0xa00000, size 0xa20000
10616832 bytes written: OK

NAND write: device 0 offset 0x5a00000, size 0xa20000
10616832 bytes written: OK
Marvell>> reset
resetting ...

BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
Warning: Unsupported freq mode for 667Mhz configured(20)
Warning: Unsupported freq mode for 667Mhz configured(20)
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 4294 [MHz]
L2 @ 4294 [MHz]
TClock @ 200 [MHz]
DDR3 @ 4294 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:1, next_record:15

[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x227800

Updating boot_count ...
[boot_count_write] offset:0x227800 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map: Code: 0x1feab000:0x1ff75c30
BSS: 0x1ffef564
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-Boot Environment: 0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: ARM OpenWrt Linux-4.14.241
Created: 2021-07-29 19:50:28 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2518258 Bytes = 2.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

[chadster766]

Are you using Putty to upload the image or something else?